Many people like to use the necklace. In fact, the necklace can be edited by itself, but the nodes of these necklace ropes should be edited well. Otherwise, it will not become bigger and smaller. The method is set into the head, and now we will learn how to make these necklace eloquents together.

The knot of these necklaces Two long ropes are left at both ends of the necklace,

Then add a bead to the tail of the rope. Straighten at both ends.

The direction of the two mouths is the opposite, and then put a rope up, then edit the rope on it, put the left side on the left side, and put the left side on the left side. Roll to the right. Then put the two ropes up.

and then tightened, then follow this method to go to the rope. The rope came out of the rope with a very good necklace, and finally burned the rope of the rope with a lighter.
 r It is a very good -looking necklace rope to close the knot. This knot can be moved, which is particularly convenient.
There are two methods of necklace rope: This rope expansion knot method 1 Step. 1. Take two ropes as A and B, and then take a red rope horizontally and placed below A and B Essence Step 2. Divide the two ends of the red rope into left 1, right 2, and 2 to be pressed below 1. 1 Pass through the AB rope and tied into the circle 2. It step 3. Place 1 below 2, 2 through the two ropes of AB through the circle of tied to 1, and a small bag will appear on the right after tightening. Step 4. Repeat step two and three, and a telescopic buckle appears. This rope expansion and knotting method 2 The dual -line can be used as the above method, so how to operate a single line? . Take a long line. Long length, leave the space for deduction. 2. Put the end of the line on the hand two circles. Pay attention to the order and location of the two laps (the second lap should be suppressed in the first circle) 3. The short line head is from Through the two laps, the other end of the long line passes from the inside of the two coils in the opposite direction. 4. Then adjust the length and tighten the two wires of the coil, but do not leave too much on the remaining lines. Tightening one with the necklace line. 5. Turn over the knot, and use the same method to make a buckle in the other end of the online. At this time, the required necklace length is adjusted, and the excess tail line is tightened. The space is easy to shrink. Cut off the excess thread with scissors. Understand, you can practice a lot of practice.
Many people like to use the necklace. In fact, the necklace can be edited by itself, but the nodes of these necklace ropes should be edited well. Otherwise, it will not become bigger and smaller. The method is set into the head, and now we will learn how to make these necklace eloquents together.

The knot of these necklaces Two long ropes are left at both ends of the necklace,

Then add a bead to the tail of the rope. Straighten at both ends.

The direction of the two mouths is the opposite, and then put a rope up, then edit the rope on it, put the left side on the left side, and put the left side on the left side. Roll to the right. Then put the two ropes up.

and then tightened, then follow this method to go to the rope. The rope came out of the rope with a very good necklace, and finally burned the rope of the rope with a lighter.
 r
It is a very good -looking necklace rope to close the knot. This knot can be moved, which is particularly convenient.
There are two methods of necklace rope:
This rope expansion knot method 1
Step. 1. Take two ropes as A and B, and then take a red rope horizontally and placed below A and B Essence
Step 2. Divide the two ends of the red rope into left 1, right 2, and 2 to be pressed below 1. 1 Pass through the AB rope and tied into the circle 2.
It step 3. Place 1 below 2, 2 through the two ropes of AB through the circle of tied to 1, and a small bag will appear on the right after tightening.
Step 4. Repeat step two and three, and a telescopic buckle appears.
This rope expansion and knotting method 2
The dual -line can be used as the above method, so how to operate a single line?
. Take a long line. Long length, leave the space for deduction.
2. Put the end of the line on the hand two circles. Pay attention to the order and location of the two laps (the second lap should be suppressed in the first circle)
3. The short line head is from Through the two laps, the other end of the long line passes from the inside of the two coils in the opposite direction.
4. Then adjust the length and tighten the two wires of the coil, but do not leave too much on the remaining lines. Tightening one with the necklace line.
5. Turn over the knot, and use the same method to make a buckle in the other end of the online. At this time, the required necklace length is adjusted, and the excess tail line is tightened. The space is easy to shrink. Cut off the excess thread with scissors. Understand, you can practice a lot of practice.