wholesale fashionable jewelry Workshop safety small knowledge

copper bezel jewelry wholesale The workshop is a transit station that implements national security policies, policies, regulations, corporate security regulations, and dissemination and feedback security information dynamics. The following is the content of the small knowledge of workshop safety production, provided it for your reference and understanding. I hope everyone likes it!
It work safety knowledge
1. Safety accidents that are prone to production workshop
The susceptible safety accidents that occur in the production workshop include electric shock, fall, scrolls, attacked objects, and fire. In order to prevent accidents, we should have necessary safety common sense and skills.
2. Electrical safety
The electric shock accident refers to the "charged" part of the human body's contact with the mechanical equipment, which causes damage accidents to the human body, and its consequences are generally serious. There are many electricity equipment in the production workshop, and there are many opportunities for each operator to contact electricals, so it is necessary to have and implement various electricity safety knowledge.
2.1 Electrical installation, inspection and maintenance of all equipment must be performed by electrical professionals, and no personnel may operate without permission.
2.2 The electrical equipment in the workshop shall not start operations at will. It can only be operated correctly according to the mechanical equipment involved in the posts I engaged in the post, and cannot exceed the prescribed operation authority. It is strictly forbidden to operate electrical equipment other than their current posts.
2.3 Electrical parts of the equipment and tools used in this position have failed. They must not be repaired privately or operate with faults; they need to report their superior contact professionals in time.
2.4 The power distribution box, power distribution board, switch switch, button switch, insertion, and wires that you often contact and use must remain intact and safe, and must not be exposed to the damage or charging part.
2.5 When operating the sword switch and magnetic switch, it must be covered to prevent the arc or fuse melting splashing injury when the arc or the fuse melter the fuse.
2.6 The shell used in the electrical equipment used in accordance with the relevant safety regulations, it is necessary to perform protective grounding or zero; and for a frequent inspection for ground or zero facilities, we must ensure that the connection, grounding or zero -zero zero must be ensured. There must be no disconnection of the wires, otherwise the ground or zero will not have any effect.
2.7 When you need to move some non -fixed -mounted electrical equipment, you must first cut off the power supply and then move. Do not pull the stretch to prevent the pull -off wire.
2.8 For the power supply connection, the socket and plug that meets the electrical safety requirements must be used in conjunction, and it is necessary to ensure that it is well -touched and the plug is not naked. It is strictly forbidden to insert the wire directly into the socket.
2.9 For equipment tools that need to be used such as vacuum cleaners, manual electric diamonds, etc., a leakage protector must be set up. At the same time, the metal shell of the tool should be carried out or zero. Heavy pressure or puncture to prevent the occurrence of leakage.
. 2.10 When placing liquid -like items, it should be placed in the position where it is not easy to touch and the liquid will not penetrate the liquid even if the liquid will not penetrate.
. 2.11 When wiping the device, it is strictly forbidden to rinse with water or wipe wiping cloth to wipe the electrical facilities to prevent short circuit and electric shock accidents.
. 2.12 When the plug is inserted into the socket for a long time (usually more than one year), the dust at least once a year is dumped at least once a year to prevent short circuit and electric shock accidents.

3. Prevention of the falling accident
The falling system means that people fall in unsafe behaviors and things at high places and fall in an unsafe state. Falling may cause serious injuries or even death. Regulations stipulate that the workplace with a height of more than 2 meters is "high", but it does not mean that only 2 meters are dangerous. Even if it falls from 1 meter high, it may cause serious injuries or death if you encounter a damage part of the body. Therefore, you need to pay attention to related safety matters when you are in high assignments. 3.1 The operators cannot stand on the operation of multiple small objects or can roll on an operation. If the sunlight is replaced, the transfer chair must not be placed on the workbench. The transfer chair rotates the body and loses the balance when the transfer chair is turned.
3.2 In principle, it is stipulated that the use of human character ladders to engage in temporary high -altitude operations must ensure that there are connections in the middle of the human character ladder (avoid its cross -open) and non -slip wear -resistant plastic cases in the four feet. Words, try to avoid standing directly at the top.
. 3.3 need to use vigorous operations at a high place. You must control the force and not be too fierce. If necessary, the seat belt is fixed on the fixed object when necessary. If the screws are excessive at the height, the wrench fell down and fell down.
3.4 When climbing the ladder, you must use one hand to support the ladder, and observe the ladder step by step; to prevent the foot of the air and fall down from the ladder.
3.5 When moving objects at a high place, it is necessary to ensure that the walking route is unobstructed and does not slide and watched the road with the eyes to prevent losing the balance from the high place from the height.
3.6 When carrying large items to the stairs, it must be steadily picked up step by step to prevent the stairs from the stairs of the stairs.
3.7 When you go down the stairs at the level, you need to watch the ladder surface step by step, and to prevent it from stepping on or sliding down from the air or sliding down from the high place because of the urgency.
3.8 When you transfer items at the opening, try to use the guardrail to ensure that the ground does not slip, the operating shoes do not slip, and stand on the stability before pulling the items. Eliminate the items swaying and dragging people towards the opening.
4. Prevention of being clamped
This accidents in the production workshop often occur in the paralysis of the operator, ignoring the potential danger of work. Therefore, you need to pay attention to the following matters to prevent the accidental accidents.
4.1 When changing the material or processing abnormality in the chip machine, the top cover must be opened to prevent abnormalities.
4.2 In maintenance, maintenance machines and entering the machine guardrail, a warning sign must be stopped and a warning sign indicates that the machine is in "maintenance" or "prohibiting boot".
4.3 In many people engaged in the same work, it is necessary to check the danger in the form of self -answering and self -answers, and execute the call to confirm the safety.
4.4 The operator must wear a job hat, gather hair in the hat, and tie up the cuffs of the workers to prevent the motion components from rolling hair and clothes to harm the human body.
4.5 When moving and stacking four corners, you need to lightly put it carefully. After lifting or putting down the end, gradually extend your hands into the bottom or move out of the edges and then lift it or let go.
5. The prevention of objects to strike
The accidents caused by an object that is splashed or falling by an object to hit the human body. Therefore, pay attention to the following matters to prevent objects from cracking down on human accidents.
5.1 When the objects are stacked, they must be stacked layer by layer. Nearly two layers of objects need to be crossed and pressed without directly superimposed; and the height stacked according to its weight is stacked to prevent the collapse and pouring accidents.
5.2 During the use of items, it is taken down layer by layer to prevent single -column access to a single column to separate and produces a crackdown.
5.3 Personnel who operate at a high place need to place the items or tools in a safe place. When using and replacing the tools, be careful and ensure that the hand is stabilized and eliminates the crackdown.
5.4 When disassembling objects, you need to help objects or support it with other objects. The other hand is operated to prevent the object from falling into the human body.
5.5 The transmitting items between people is required to be passed on in principle. The person who confirms that the receiver has stabilized the biological person to let go; it is forbidden to parabore and throw objects from a distance.
5.6 At the item lifting site, the suspender rope on the suspension must be locked, and the personnel are prohibited from standing and engaged in other operations under the running route of the hanging objects.
6. Safety measures for flammable and explosive dangerous goods
We production workshops We have often used some flammable and explosive dangerous items, such as alcohol, carlite, paint and laundry water, etc. Once the transportation and storage process is not well managed or improperly used, it is easy to cause fire and explosion accidents, cause casualties, equipment damage, etc., causing inestimable losses to the factory. Therefore, fire explosion -proof is a very important task. As a member of the company, we must learn and master the necessary safety knowledge.
6.1 Smoking in the production workshop according to the factory is strictly banned, and the cigarette butt is strictly prohibited in the smoking area.
6.2 Various types of flammable and explosive items must be stored in the specified seal container in use, and accurately guarantees easy identification. It is strictly forbidden to use mineral water bottle to place any items.
6.3 Using Minghuo operation at the work site, it is necessary to report to the production manager for approval and the necessary safety protection measures.
6.4 Do not use electrical appliances that are easy to generate in the storage places of flammable and explosive items, such as mobile phones, welding machines and electromo mills.
6.5 Fire protection facilities arranged by the production workshop such as fire extinguishers and fire hydrants should be checked at any time, and they should learn and master their usage methods and applicable scope; any personnel open and adjust their storage positions at will when a fire occurs.
6.6 The storage of flammable and explosive dangerous goods should be specifically planned to stay away from the power box, machinery and equipment, and designate a special person to be responsible for inspection and management.
6.7 It is strictly forbidden to use the floor and machinery of the workshop to clean the workshop.
7. Elevator safety
The elevator should pay attention to the following safety issues during the use and maintenance process of elevators:
7.1 must be implemented in accordance with the established elevator safety management system, set up special personnel management, and regularly perform maintenance , Maintenance and maintenance.
7.2 The production of elevators can only be carried and ensure that the items are placed stably. If you put it on the forklift, you should lower the forklift and let the card board directly contact the elevator surface; it is forbidden to take the elevator.
7.3 The elevator should be stopped to use abnormal running. Immediately reported that the higher -level liaison elevator repair managers should be maintained for maintenance.
7.4 It is strictly forbidden to smoke and play in the elevator. Do not mess up the switch in the elevator at will.
7.5 When a fire occurs, the elevator cannot be taken.
7.6 The single weight of the elevator transport items is not allowed to exceed its rated allowable load weight.
8. Safety of forklifts
Due to the many forklifts and manual or electric operations, and often carrying items in smaller spaces, the implementation of the following safety measures is needed:
8.1 Before using and after use, it is necessary to check it: the motor wheel rotation is flexible, whether the lifting is flexible, etc. It is found that the superior to report the overhaul in time, and it is strictly forbidden to let the forklift belt to run.
8.2 forklifts must be used by specialized personnel who have been operated, and other personnel are prohibited from opening and use.
8.3 The weight of the items on the forklift must be less than its allowed load. If a single (or batch or piece) item is too heavy, multiple forklifts need to be uniformly divided into weights for transportation; or small batch handling.
8.4 If you use the cardboard to transport items, you need to use the appropriate size of the card board and try to make the forklift of the forklift as wide as possible to ensure its safety and stability.
8.5 When stacking items, it is necessary to confirm that it is not loose, and use a dedicated belt or rope to prevent loosening and collapse during transportation.
8.6 The items placed on the forklift must ensure that the location and weight are good.
8.7 must not raise items on the tilted road. Be careful when turning, uphill and downhill. If necessary, reduce the speed of handling and use other reinforcements to ensure safety Harmony with the human body.
8.8 It is strictly forbidden to work under the forklift's arms, and it is not allowed to extend the hands and feet into the fixed column to stabilize items.
8.9 When moving the items, try to reduce the height of the forklift's extension to reduce its center of gravity and increase its stability.
8.10 forklifts to start and stop the abnormalities caused by excessive speed. During the transportation process, check whether there are other operators and foreign bodies blocking the running area at any time.
8.11 When moving items, pay attention to the running road situation to strictly control the speed to prevent hitting machinery and equipment, walls and doors; pay special attention to reducing the speed of the vehicle in the turning and slippery ground.
8 12 forklifts During the movement, personnel are strictly prohibited from standing on it and passengers.
8.13 When a forklift is fixed in space such as the door, elevator and other spaces, it is necessary to pay attention to the width and height of the items that cannot exceed the size of the door, prevent the tilt of the door and the collapse of the items.
8.14 When turning, confirm that there is no person and foreign body from the other side, and try to turn with a large arc as much as possible. At the same time, pay attention to the collision of the tail and corners of the forklift.